ANCHOR

Resin-A GE-410C (Cartridge type)

Resin anchor (Injection System)

  • ■Uses resin for cold area with short hardening time.
  • ■Can be used for various bolts, sizes and shapes of different reinforced steels.
  • ■Used extensively for concrete, brick, stone material and hollow base material.
  • ■Demonstrates stable fixing strength because primary material and hardening agent are constantly mixed by mixing nozzle.
  • ■Adopts a highly alkali resistant epoxy acrylate resin.

GE-410C series

Resin-A GE-410C (Cartridge type)

unika news PDF (2.01MB)

Uses

Concrete•Stone material•Hollow base material•ALC

Installation method

  1. Drill vertically to target surface with the determined preparation diameter and preparation hole depth.
  2. Use a dust collector or blower to thoroughly remove chips in the hole.
  3. Remove chips adhered in the hole using a brush, and use a dust collector or blower to clean in the hole again.
  4. Insert the nozzle down to the hole bottom and fill resin.
  5. Insert the bolt down to the hole bottom while slowly turning it by hand.
  6. Do not move the anchor bolt within the determined hardening time after embedding.

■Installation explanatory video

Resin-A GE-410C (Cartridge type) Installation explanatory video

Smart phone and a tablet is here.

■Uses

Foundation work for iron frame, Passage construction work, Tunnel construction work, Installation for vibrating machines.

■Installation specifications

 Nominal
diameter(mm)		 M8 M10 M12 M16 M20 M22 M24
 Preparation
hole
diameter(mm)		 10.0 12.0 14.0 18.0 24.0 25.0 28.0
 Embedment
depth(mm)		 80 90 110 130 170 190 210
 Required
resin
amount(ml)		 4 6 9 15 42 43 66
 Recommended
tightening
torque(Nm)		 10 20 40 80 120 140 160
 Number of pieces
installed(Pcs.)		 92 62 40 25 8 8 5

*Number of pieces installed is for reference number of pieces at a loss rate of 20%.

■Plastic sleeve installation specifications

Nominal
diameter(mm)		 M8 M10 M12
Preparation hole
diameter(mm)		 16.0 16.0 20.0
Matching
sleeve(Code)		 RA-P1685 RA-P1685 RA-P2085
Required resin
amount(ml)		 30 30 40

■Structural Drawing

Structural Drawing

■Installation Example

  • Continuous thread bolt

  • Plastic sleeve

■Shape of bolt used

Shape of bolt used

Cannot be used for a round bar. Use bolts which have irregularity on a surface such as a continuous thread bolt and different shape bar steel.

■Guideline for hardening time

 Temperature(℃) -18 -10 -5 0 15
 Use time(minutes) 90 40 25 15 5
 Hardening time(minutes) 540 150 75 45 15

(Do not move the anchor reinforcement within the hardening time.)

Precautions on use

  • Avoid direct sunlight and store in a well-ventilated place where the temperature does not rise so high.
    (Never raise the temperature above 40℃. Always keep the temperature in the range of 5 to 25℃.)
  • Do not bring close to fire or high temperature objects.
  • Cartridge can be stored until the expiration date for use under standard storage conditions.
  • Wear protective equipment (such as protective glasses and mask) when using.
  • When resin adheres to skin, irritation may occur in rare cases. Take action such as immediately wiping and rinsing with a hot soapy solution.
    In addition, if resin gets into eyes, immediately rinse with a large amount of water and seek medical attention.

Precautions on installation

  • Make sure to provide the drilling diameter and drilling depth as described in the specifications.
  • Make sure to use both a metallic brush and blower to sufficiently clean inside the hole.
  • Make sure to mount the mixing nozzle with it just before use.
  • Make sure to discard first approximately 20~30cc at a time of first use and nozzle replacement. (Mixing improperly may result in reduction in strength.)
  • This cannot be used for a steel bar with no irregularity such as a round bar.
  • Refer to the scale on the cartridge label for discharge resin amount.
  • Do not move the bar steel nor apply load within the determined hardening time.
GE-C type (Resin cartridge)
Size Capacity(ml) Content(Pc.) JAN Code
GE-410C 410 GE-410C Cartridge*1 Mixing nozzle*2 4989270930353

GE type exclusive parts
Product name Size Matching cartridge JAN Code Appearance
Mixing nozzle(3 Pcs.) RA-MX3 GE 4989270930179
Injection gun 410 RA-GUN410 GE-410 4989270930148
Air gun 410 RA-AGUN410 GE-410 4989270930315

*Used air pressure: 0.6~1MPa

Installation specifications
Use bolt
different shape
reinforced steel		 Preparation
hole
diameter
(mm)		 Embedment
depth
(mm)		 Required
resin
amount
(ml)		 Recommended
tightening
torque
(Nm)		 Max.
extraction
strength
(KN)		 Number of
pieces
installed
(Pcs.)
M8 10.0 80 10 4 20.3 93
M10 12.0 90 20 6 36.4 63
D10 13.0 - 7 33.6 56
M12 14.0 110 40 9 42.5 40
D13 15.0 - 7 62.4 56
M16 18.0 130 80 15 78.2 24
D16 20.0 - 17 88.5 20
M20 24.0 170 120 42 125.3 8
D19 25.0 - 42 146.7 9
M22 25.0 190 140 43 144.5 8
D22 28.0 - 52 167.3 7
M24 28.0 210 160 66 167.7 5
D25 32.0 - 75 208.2 5
M30 35.0 280 200 135 - 2
D29 38.0 - 165 - 2
  • *FC=21N/mm2

■Related items

Push pump
Size Specifications JAN Code Appearance
RA-PUP (Nozzle diameter)
10mm
(Hose length)
270mm		 4989270930162
Metal brush
Size Specifications JAN Code Appearance
RA-MB10 Φ10*300 4989270930292
RA-MB13 Φ13*300 4989270930193
RA-MB18 Φ18*300 4989270930209
RA-MB28 Φ28*300 4989270930216
Extension nozzle(including three)
Size Specification JAN Code Appearance
RA-EXP3 Φ8×1m 4989270930445
Plastic sleeve (including 10 pieces)
Size Specifications JAN Code Appearance
RA-P1685 16*85(M8/10) 4989270930599
RA-P2085 20*85(M12) 4989270930261

Site Map

Copyright(C) 2012 UNIKA CO., LTD. All rights reserved.